MASTER FLASH®

QUALITY & SERVICE WORLDWIDE

Design Excellence

Master Flash® design meets all roofing needs. Sleeve flexibility accommodates vibration and pipe movement caused by expansion contraction. The soft aluminum base easily conforms to most metal roof profiles.

Weather Protection

Made or EPDM, these flashings are compounded specifically for maximum resistance to weathering due to ozone and ultraviolet light.

Base Flexibility

The base is designed to form a seal on most panel configurations and roof pitches regardless of pipe location.

Easy On-Site Customization

Fast, one piece construction allows for easy on-site installation usually 5 minutes.

Modification Made Simple

Easy to see pipe diameters make for painless on-site installation.

Standard Master Flash®

• 9 sizes, designed for 1/4” to 28-1/2” (6 - 723mm) diameter pipes
• Easy on-site installation in usually 5 minutes
• The soft aluminum base easily conforms to most metal roof profiles
• Pipe diameters can be seen clearly for proper pipe fitting

Solar Multi-Port - MR Master Flash®

5 Port Design for the Metal Roofing Industry

• Accommodates:

 ONE 0” - 1-15/16” (0 - 49mm) pipe

 TWO 3/8” (9.6mm) pipe / cable

 TWO 3/4” (20mm) pipe / cable

Extreme Angle Master Flash®

• Designed for 1/4” to 5-3/4” (6 - 146mm) diameter pipes
• Easy on-site installation in usually 5 minutes
• The built in 40º degree pitch allows to handle any extreme roof pitch (35º - 65º)
• Sleeve flexibility accommodates vibration and pipe movement caused by expansion contraction

Square Vent Master Flash®

• 2 sizes/EPDM/designed for 2-1/2” to 5” (63 - 127mm) diameter pipes
• Made to withstand the damaging effects of ultraviolet light and ozone
• Easy install snaps included, specially designed for square vent applications
• Sleeve flexibility accommodates vibration and pipe movement caused by expansion/contraction

Multi-Flash Master Flash® Two Flashings in ONE!

• 9 Sizes, designed for 1/4” to 28-1/2” (6 - 723mm) diameter pipes
• Smooth cut is intended to eliminate use of razor blades
• Stainless steel gripper to secure a retro custom fit
• Gripper available upon request

Universal Master Flash®

• All around performance
• 9 sizes, designed for 1/4” to 19” (6 - 482mm) diameter pipes
• Easy on-site customization can accommodate all normal installations

Universal Retrofit Master Flash®

• 3 sizes, designed for 3/4” (19mm) to 10” (254mm) diameter pipes
• Fast, one piece construction allows for easy on-site install in usually 5 minutes

* Master Flash; the only CSA Approved EPDM rubber flashing.

Retrofit Master Flash®

• 3 sizes, designed for 1/2” to 16-1/4” (12 - 412mm) diameter pipes
• Easy to see pipe diameters make for painless on site customization
• Easily installed fastener snaps included

• 4-1/2” (114mm) base

• Up to 4 cables or wires per flashing
• Extra ports to accommodate copper pipe and electrical cabling
• Easy install for solar applications

Solar-Flash Master Flash®

• Specifically designed for solar applications
• Designed for 3/4” (19mm) to 1” (25mm) diameter pipes
• Pre-cut hole for pipe sizes 3/4” (19mm) to 1” (25mm) allowing for minimal on-site preparation and assembly
• The pitch canal allows for maximum flexibility, easily accommodating up to a 60º degree pitch without affecting performance

The only ICC listed flashing for the Metal Building Industry with a 35 year warranty

• 11 Sizes / Designed for 1 /8” to 28-1 /2” (3-723mm) diameter pipes
• On-site customization
• Designed for 1/4” to 13” (6-330mm) diameter pipes
• Pipe diameters can be seen clearly for proper pipe fitting